Router RUTX08

WAN:1 x WAN port 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover

LAN:3 x LAN ports, 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover

Routing:Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, NHRP)

Network protocols:TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SMNP, MQTT, Wake On Lan (WOL)

VoIP passthrough support:H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Connection monitoring:Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection

Firewall:Port forward, traffic rules, custom rules

DHCP:Static and dynamic IP allocation, DHCP Relay, Relayd

QoS / Smart Queue Management (SQM):Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e

DDNS:Supported >25 service providers, others can be configured manually

Network backup:VRRP, Wired options, each of which can be used as an automatic Failover

Load balancing:Balance Internet traffic over multiple WAN connections

SSHFS:Possibility to mount remote file system via SSH protocol

Authentication:Pre-shared key, digital certificates, X.509 certificates, TACACS+, Radius, IP & Login attempts block

Firewall:Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T

Attack prevention:DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)

VLAN:Port and tag based VLAN separation

WEB filter:Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only

Access control:Flexible access control of TCP, UDP, ICMP packets, MAC address filter

OpenVPN:Multiple clients and a server can run simultaneously, 27 encryption methods

OpenVPN Encryption:DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,

BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256

IPsec:IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)

GRE:GRE tunnel, GRE tunnel over IPsec support

PPTP, L2TP:Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support

Stunnel:Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code

DMVPN:Method of building scalable IPsec VPNs

SSTP:SSTP client instance support

ZeroTier:ZeroTier VPN client support

WireGuard:WireGuard VPN client and server support

Tinc:Tinc offers encryption, authentication and compression in it’s tunnels. Client and server support.

ID range:Respond to one ID in range [1;255] or any

Allow Remote Access:Allow access through WAN

Custom registers:MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Slave functionality

Supported functions:01, 02, 03, 04, 05, 06, 15, 16

Supported data formats:8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC)

Protocol:HTTP(S), MQTT, Azure MQTT

MQTT Gateway:Allows sending commands and receiving data from MODBUS Master through MQTT broker

Supported modes:TCP Master, DNP3 Outstation

WEB UI:HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log

FOTA:Firmware update from server, automatic notification

SSH:SSH (v1, v2)

TR-069:OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem

MQTT:MQTT Broker, MQTT publisher

SNMP:SNMP (v1, v2, v3), SNMP Trap

JSON-RPC:Management API over HTTP/HTTPS

MODBUS:MODBUS TCP status/control

RMS:Teltonika Remote Management System (RMS)

Cloud of Things:Allows monitoring of: Device data, Mobile data, Network info, Availability

ThingWorx:Allows monitoring of: WAN Type, WAN IP

Cumulocity:Allows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP

Azure IoT Hub:Can send device IP, Number of bytes send/received, Temperature, PIN count to Azure IoT Hub server

CPU:Quad-core ARM Cortex A7, 717 MHz

RAM:256 MB, DDR3

FLASH storage:256 MB, SPI Flash

WEB UI:Update FW from file, check FW on server, configuration profiles, configuration backup

FOTA:Update FW

RMS:Update FW/configuration for multiple devices at once

Keep settings:Update FW without losing current configuration

Operating system:RutOS (OpenWrt based Linux OS)

Supported languages:Busybox shell, Lua, C, C++

Development tools:SDK package with build environment provided

Data rate:USB 2.0

Applications:Samba share, USB-to-serial

External devices:Possibility to connect external HDD, flash drive, additional modem, printer

Storage formats:FAT, FAT32, NTFS

Input:1 x Digital Input, 0 – 6 V detected as logic low, 8 – 30 V detected as logic high

Output:1 x Digital Output, Open collector output, max output 30 V, 300 mA

Events:Email, RMS

I/O juggler:Allows to set certain I/O conditions to initiate event

Connector:4-pin industrial DC power socket

Input voltage range:9 – 50 VDC, reverse polarity protection, voltage surge/transient protection

PoE (passive):Passive PoE over spare pairs. Possibility to power up through LAN port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards, Mode B, LAN1 Port, 9 – 50 VDC

Power consumption:6 W Max

Ethernet:4 x RJ45 ports, 10/100/1000 Mbps

I/O’s:1 x Digital Input, 1 x Digital Output on 4-pin power connector

Status LEDs:8 x LAN status LEDs, 1 x Power LED

Power:1 x 4-pin power connector

USB:1 x USB A port for external devices

Reset:Reboot/User default reset/Factory reset button

Other:1 x Grounding screw

Casing material:Aluminium housing with DIN rail mounting option

Dimensions (W x H x D):115 x 32.2 x 95.2 mm

Weight:345 g

Mounting options:DIN rail, flat surface placement

Operating temperature:-40 °C to 75 °C

Operating humidity:10% to 90% non-condensing

Ingress Protection Rating:IP30

Regulatory:CE, RoHS, REACH

Standards:EN 55032:2015, EN 55035:2017

ESD:EN 61000-4-2:2009

RS:EN 61000-4-3:2006 + A1:2008 + A2:2010

EFT:EN 61000-4-4:2012

Surge protection:EN 61000-4-5:2014

CS:EN 61000-4-6:2014

DIP:EN 61000-4-11:2004

Standards:IEC 62368-1:2014 EN 62368-1:2014+A11:2017